Leveling, Chocks & Stabilizing
X-Chocks For Wide Stance Axles
If your tandem axles are spaced further apart than most, the X-Chock everyone recommends physically will not close on your gap. Measure first, then pick from the three products that reach.
By Mike M. ·
How this page is funded: we earn a commission if you buy through our links, at no extra cost to you. It never changes which product we rank first. Prices come from Amazon and are read automatically — each one shows the date it was read. Full disclosure.
Top pick
Our pick on this page
X-Chock Tire Locking Chock, Extended, 28014
The same scissor mechanism as the standard X-Chock on a longer body, published as fitting tire spacing up to 17 in. Sold as one chock and one handle per box rather than as a pair, which is the detail that catches people out.
$55.07 21% off
Price as of November 18, 2026. #ad How this is funded
Read the full write-up or compare it with the rest below.
Quick picks
Ranked for one job: closing a gap the standard X-Chock cannot reach. Scored on the published chock rubric - holding force (35%), fit range (25%), everyday usability (20%), build (10%), price (10%) - with fit range doing most of the work, because on this page a chock that does not reach scores zero regardless of how well it is made.
| # | Product | Best for | Score | Price |
|---|---|---|---|---|
| 1 | X-Chock Tire Locking Chock, Extended, 28014 The same scissor mechanism as the standard X-Chock on a longer body, published as fitting tire spacing up to 17 in. Sold as one chock and one handle per box rather than as a pair, which is the detail that catches people out. Top pick | A tandem axle whose tires sit too far apart for the standard X-Chock | 9.1/10 | $43.63X-Chock Tire Locking Chock on Amazon
|
| 2 | Camper X Wheel Chocks, 4 to 17 in, 2-Pack An X-shaped stabilizer whose listing publishes a 4 to 17 in adjustment range and ships two per box, which is the combination the BAL extended does not offer. The trade is a less established name behind it. Best value pair | Covering a wide gap with two chocks for the price of one BAL extended | 9.0/10 | |
| 3 | X-Shaped RV Wheel Stabilizer Chocks, 3 to 11.5 in, 2-Pack Publishes a 3 to 11.5 in range and takes a drill rather than a hand ratchet. It is the pick for the common case where your gap measures 10.5 or 11 in and the standard chock will not quite close on it. For a gap just past 10 in | A gap just past where the standard X-Chock runs out | 8.8/10 | |
| 4 | X-Chock Wheel Stabilizer, Pair, 28012 Wedges between the two tires of a tandem axle and screws out against both. It is doing a different job from a chock — it stops the trailer rocking rather than stopping it rolling. The standard, and where it stops | Stopping the rocking motion on a tandem-axle trailer | 8.9/10 | |
| 5 | MaxxHaul Solid Rubber Wheel Chock, 2-Pack, 70472 Solid rubber rather than hollow plastic, with non-slip pads. On a slope or a polished garage floor this is the one that stays put, which is the only specification that matters. When nothing X-shaped fits | Chocking on a slope or on smooth concrete | 9.4/10 |
Tap any row to jump to the full write-up. Prices come from Amazon and are read automatically — see each product below for the date.
The short answer
This page exists because the standard advice fails silently on certain trailers. Every leveling guide on the internet, including ours, tells a new travel trailer owner to buy an X-Chock to stop the rocking motion. Then the chock arrives, you wind the handle all the way out, and the arms stop a good two inches short of your tires. Nothing is faulty. Your axles are simply spaced wider than the chock was designed for, and no amount of winding is going to fix it.
Wide axle spacing is common enough to be worth a page. Retailers that sell the extended chock list it against trailer families such as Bullet, LaCrosse, Prime Time, Passport and North Trail, and the pattern holds more broadly: longer trailers and half-ton-towable models with long leaf springs tend to carry more distance between the axles than a compact bunkhouse does. If you are towing one of those, your hitch choice follows the trailer weight and your chock choice follows the axle spacing, and the two have nothing to do with each other.
Wide stance / wide track axle: not an official spec with a cut-off, just the trade’s phrase for tandem axles spaced far enough apart that a standard scissor chock will not span the gap. BAL sells its extended chock explicitly “for use with wide track axle” applications, which is as close to a definition as the industry gets. The practical test is your tape measure, not a label on the trailer.
Measure the gap - the only step that matters
Everything on this page depends on one number, and getting it wrong wastes both the money and the trip. Take the measurement before you open a browser tab.
- 1
Park on level ground, hitched
Not on a slope and not on blocks. A trailer sitting nose-down or propped on one side moves the tires relative to each other and gives you a number you cannot trust. Level it properly first if you need to - the sequence is here. - 2
Measure tread to tread, at axle height
Put the tape across the gap between the two tires at roughly the height of the axle centerline, from the back face of the front tire to the front face of the rear tire. That is the span the chock arms have to cover. Measuring at the bottom of the tire where it bulges gives you a smaller, flattering number that the chock will not actually meet. - 3
Write the number down and check both sides
They should match, and if they do not, use the larger one. A difference of more than a quarter inch side to side is worth looking into on its own, because it can point at a bent spring hanger or a shifted axle. - 4
Compare it against the published ranges, not the photos
The table below is the published figures. If your number lands within a half inch of the top of a product’s range, go up a size - a chock at the absolute end of its travel has almost no thread left to take load.
| Product | Published fit range | Chocks per box |
|---|---|---|
| BAL X-Chock 28012 (standard) | 1-3/8 in to 10 in | 2, one handle |
| BAL X-Chock 28014 (extended) | Up to 17 in | 1, one handle |
| Camper X stabilizer | 4 in to 17 in | 2 |
| X-shaped drill-adjust stabilizer | 3 in to 11.5 in | 2 |
| Conventional rubber chock | Not applicable - goes in front of the tire | 2 |
The common mistake
What an X-chock does, and what it does not
Worth being clear about, because it changes how much you should spend. An X-shaped chock wedges between the two tires of a tandem axle and screws outward against both, which removes the small fore-and-aft movement the suspension allows. That movement is what makes a parked trailer feel like it is rocking when someone walks across the floor. Killing it is the most noticeable single upgrade to how solid a trailer feels at a site, which is why these things are recommended so universally.
What it is not is a brake. It does not stop the trailer rolling, and on a slope it will not hold the trailer at all — the whole assembly can roll with the tires, because it is gripping the tires rather than the ground. The full distinction is here, and the short version is that you need both: a conventional chock in front of or behind a tire to stop rolling, and an X-chock between the tires to stop rocking. How many chocks you actually need answers the count question.
The reason this matters on a wide-stance trailer specifically: an extended X-chock costs roughly twice a standard one once you have bought two boxes. For a part that improves how the floor feels rather than whether the trailer stays put, it is reasonable to decide the money goes on conventional chocks and stabilizer jacks instead. That is a legitimate choice and this page is not going to pretend otherwise.
What fits, in order
BAL X-Chock 28014, extended — top pick. This is BAL’s own answer to the problem: the same scissor mechanism and steel body as the chock everyone recommends, on a longer frame, published as fitting tire spacing up to 17 in and sold explicitly for wide track axles. The mechanism has decades behind it, the ratchet handle is the same one, and it is the only product here from a maker with a long RV track record. The cons are genuine and they are about cost and scope. One chock and one handle per box means a tandem axle costs two boxes, which makes it comfortably the most expensive way to solve this. BAL does not publish a minimum spacing for it, so if your gap is near 10 in you are guessing whether the extended or the standard chock is the better fit. And like every X-chock it does nothing at all on a single-axle trailer.
Camper X 4 to 17 in pair — best value pair. This is the pick if the doubled cost of the BAL route is the deciding factor. The listing publishes a 4 to 17 in adjustment range, which spans both standard and wide-track spacing, and it ships two chocks in one box — so a single purchase does a tandem axle, at a fraction of two extended BALs. The honest trade: there is no long service history behind the name, the way there is behind BAL, so you are buying a published range rather than a reputation. A product that covers 4 in to 17 in in one body is also necessarily a compromise at both ends of that span. And sellers word the pack count inconsistently on listings like this, so read the quantity on the page you actually order from before you click.
X-shaped drill-adjust stabilizer, 3 to 11.5 in — for a gap just past 10 in. There is a very common case this one exists for: you measured 10.5 or 11 in, the standard BAL will not quite close, and the extended chock is far more range than you need at twice the price. This publishes a 3 to 11.5 in range, comes two to a box, and takes a drill rather than a hand ratchet, which is quicker when you are setting up in the dark. The cons: it stops well short of a genuinely wide 14 to 17 in stance, so it is no use if your number is up there; drill adjustment makes over-tightening easy and a bent screw is how these die; and the brand publishes no load or torque figure at all.
BAL X-Chock 28012, standard — the one to buy if your gap is under 10 in. Included here deliberately, because a good proportion of people who land on a wide-stance page measure their gap and find it was never wide. Retailers publish 1-3/8 in to 10 in for this one, it is the pick on our X-chock roundup, and it is sold as a pair with one handle, so one box does a tandem axle. Buy it if your number fits. The cons are the same as any X-chock: useless on a single axle, not a substitute for a real chock on a slope, and fiddly to fit if the tires sit close together.
MaxxHaul solid rubber chock — when nothing X-shaped fits. The fallback that is also the only option on some trailers. If you have a single axle, or triple axles with uneven spacing, or your measurement came out above 17 in, there is no X-chock in this field for you and you should stop looking for one. A pair of solid rubber chocks in front of and behind one tire on each side does the job an X-chock cannot anyway — stopping the trailer from moving — and a set of stabilizer jacks addresses the rocking from underneath instead of between the tires. The cons: it does nothing for fore-and-aft suspension movement, so the floor will still have some give, and rubber chocks take up more storage than their size suggests.
What to remember
- Measure tread to tread at axle height, on level ground, before you buy anything.
- Standard BAL X-Chock 28012: published 1-3/8 in to 10 in, sold as a pair.
- Extended BAL X-Chock 28014: published up to 17 in, sold ONE per box.
- A tandem axle needs two extended chocks, so budget for two boxes.
- Gap at 10.5 to 11.5 in? The drill-adjust pair is cheaper than going extended.
- Over 17 in, single axle, or uneven triple axles: no X-chock fits. Use conventional chocks.
- An X-chock stops rocking, never rolling. You still need a chock on the ground.
How we picked
We have not fitted these to a wide-stance trailer and we do not own one. This page is built on published fit ranges and published pack counts, because on this particular problem those two figures decide everything — a beautifully made chock that stops two inches short of your tires is worth nothing, and a chock you bought one of when you needed two solves half the trailer. BAL’s figures come from retailer listings for parts 28012 and 28014, including PPL Motor Homes, which states both the 17 in maximum and the one-chock-per-box packing; where BAL publishes no minimum spacing for the extended chock, the table says so rather than carrying a figure. The two X-shaped stabilizers publish their ranges on their own listings and no load figures at all, and they are scored down for that absence. Every listing was confirmed live and in stock before it was featured. Your own tape measure governs over anything here. Current prices come from retailer listing data read automatically and date-stamped. The rubric and its weights are published on how we pick.
The picks in full

X-Chock Tire Locking Chock, Extended, 28014
BAL · Best for a tandem axle whose tires sit too far apart for the standard x-chock
The same scissor mechanism as the standard X-Chock on a longer body, published as fitting tire spacing up to 17 in. Sold as one chock and one handle per box rather than as a pair, which is the detail that catches people out.
Key specifications
- Fits
- Tire spacing up to 17 in
- Pack
- One chock and one handle per box
- Part
- 28014
- Action
- Scissor wedge, ratchet-tightened
Capacity figures read from PPL Motor Homes published X-Chock Xtended Fit listing, October 2026.
How it scored
- Holding force (35%)7
- Fit range (25%)9
- Everyday usability (20%)7
- Build quality (10%)9
- Price for capability (10%)5
The figures above, at the weights above, converted to our published 8.4–9.8 scale by one site-wide formula. Both the weights and the formula are on how we pick, so this number is reproducible from this card.
Why we picked it
- Reaches a gap the standard 28012 physically cannot close
- Same proven ratchet mechanism and steel body as the standard chock
- Sold for wide-track axles specifically rather than as a universal claim
Good to know
One chock per box - a tandem axle needs two boxes, so the real cost doubles
$55.07 21% off
Price as of November 18, 2026. #ad How this is funded

Camper X Wheel Chocks, 4 to 17 in, 2-Pack
Camper X · Best for covering a wide gap with two chocks for the price of one bal extended
An X-shaped stabilizer whose listing publishes a 4 to 17 in adjustment range and ships two per box, which is the combination the BAL extended does not offer. The trade is a less established name behind it.
Key specifications
- Fits
- 4 to 17 in, per the listing
- Pack
- 2 chocks
- Shape
- X-shape scissor
- Stated use
- Travel trailer and fifth wheel tandem axles
How it scored
- Holding force (35%)6
- Fit range (25%)9
- Everyday usability (20%)7
- Build quality (10%)6
- Price for capability (10%)8
The figures above, at the weights above, converted to our published 8.4–9.8 scale by one site-wide formula. Both the weights and the formula are on how we pick, so this number is reproducible from this card.
Why we picked it
- Published range covers both standard and wide-track spacing
- Two chocks per box, so one purchase does a tandem axle
- The only pick here that spans the whole gap range in one product
Good to know
No long service history behind the brand, unlike BAL
Price as of November 18, 2026. #ad How this is funded

X-Shaped RV Wheel Stabilizer Chocks, 3 to 11.5 in, 2-Pack
Generic · Best for a gap just past where the standard x-chock runs out
Publishes a 3 to 11.5 in range and takes a drill rather than a hand ratchet. It is the pick for the common case where your gap measures 10.5 or 11 in and the standard chock will not quite close on it.
Key specifications
- Fits
- 3 to 11.5 in, per the listing
- Pack
- 2 chocks
- Tightening
- Drill-adjustable
- Shape
- X-shape scissor
How it scored
- Holding force (35%)6
- Fit range (25%)7
- Everyday usability (20%)7
- Build quality (10%)6
- Price for capability (10%)8
The figures above, at the weights above, converted to our published 8.4–9.8 scale by one site-wide formula. Both the weights and the formula are on how we pick, so this number is reproducible from this card.
Why we picked it
- Covers the 10 to 11.5 in band the standard BAL chock cannot reach
- Drill adjustment is faster than winding a ratchet handle by hand
- Two per box
Good to know
Stops short of a genuinely wide 14 to 17 in stance
Price as of November 18, 2026. #ad How this is funded

X-Chock Wheel Stabilizer, Pair, 28012
BAL · Best for stopping the rocking motion on a tandem-axle trailer
Wedges between the two tires of a tandem axle and screws out against both. It is doing a different job from a chock — it stops the trailer rocking rather than stopping it rolling.
Key specifications
- Pack
- Pair, one handle
- Use
- Tandem-axle trailers only
- Action
- Scissor wedge, ratchet-tightened
- Function
- Stabilizing, not primary chocking
How it scored
- Holding force (35%)6
- Fit range (25%)6
- Everyday usability (20%)8
- Build quality (10%)9
- Price for capability (10%)7
The figures above, at the weights above, converted to our published 8.4–9.8 scale by one site-wide formula. Both the weights and the formula are on how we pick, so this number is reproducible from this card.
Why we picked it
- Visibly reduces the side-to-side rock that makes a trailer feel flimsy
- Ratchets tight so it does not work loose
- One handle does both chocks
Good to know
Tandem axles only — it braces between two tires, so a single-axle trailer has no gap to fill
Price as of November 18, 2026. #ad How this is funded

MaxxHaul Solid Rubber Wheel Chock, 2-Pack, 70472
MaxxHaul · Best for chocking on a slope or on smooth concrete
Solid rubber rather than hollow plastic, with non-slip pads. On a slope or a polished garage floor this is the one that stays put, which is the only specification that matters.
Key specifications
- Size
- 8 in x 4 in x 6 in
- Material
- Solid rubber
- Feature
- Non-slip traction pads, built-in handle
- Pack
- 2 chocks
How it scored
- Holding force (35%)9
- Fit range (25%)7
- Everyday usability (20%)8
- Build quality (10%)9
- Price for capability (10%)9
The figures above, at the weights above, converted to our published 8.4–9.8 scale by one site-wide formula. Both the weights and the formula are on how we pick, so this number is reproducible from this card.
Why we picked it
- Rubber grips where plastic skates
- Solid, so it will not crush
- Handle makes placement easy
Good to know
Heavy for its size
Price as of November 18, 2026. #ad How this is funded
Our recommendation
Of the 5 picks above, these are the two to choose between.

Our pick
X-Chock Tire Locking Chock, Extended, 28014
Best for a tandem axle whose tires sit too far apart for the standard x-chock. The same scissor mechanism as the standard X-Chock on a longer body, published as fitting tire spacing up to 17 in. Sold as one chock and one handle per box rather than as a pair, which is the detail that catches people out.
$55.07 21% off
Price as of November 18, 2026. #ad How this is funded

Runner-up
Camper X Wheel Chocks, 4 to 17 in, 2-Pack
Best for covering a wide gap with two chocks for the price of one bal extended. An X-shaped stabilizer whose listing publishes a 4 to 17 in adjustment range and ships two per box, which is the combination the BAL extended does not offer. The trade is a less established name behind it.
Price as of November 18, 2026. #ad How this is funded
Common questions
Retailers publish 1-3/8 in to 10 in for the 28012, sold as a pair with one handle. Above about 10 in it will not reach.
No. The extended 28014 is one chock and one handle per box. A tandem axle needs two boxes — the standard 28012 is the one that comes as a pair.
On level ground, hitched: tread to tread at axle height, back of the front tire to the front of the rear tire. Check both sides and use the bigger number.
No X-chock fits above 17 in. Use conventional chocks on the ground plus stabilizer jacks under the frame — you lose the anti-rock effect, not the safety function.
No. It grips the tires, not the ground, so it can roll with them. It is a stabilizer, not a brake — always use a conventional chock as well.
Sources
- PPL Motor Homes published BAL X-Chock Xtended Fit listing, part 28014 - fits tire spacing up to 17 in, one chock and one handle per box — read November 2026
- Tractor Supply published BAL X-Tended Fit X-Chock listing - for use with wide track axle, part 28014 — read November 2026
- Tractor Supply published BAL X-Chock pair listing, part 28012 - for use with tandem tires — read November 2026
- Norco Industries - maker of the BAL RV product line — read November 2026
Read next
Brands: want your product tested? For Brands.