Skip to content
Trailer & Hitch

Water & Waste

RV Sewer Hose Support: 20 ft vs 30 ft

The support has to be at least as long as the hose you lay in it, because a hose that runs off the end of the trough sags - and a sag is where the smell comes from. Which means the real question is how long your hose should be.

By Mike M. ·

How this page is funded: we earn a commission if you buy through our links, at no extra cost to you. It never changes which product we rank first. Prices come from Amazon and are read automatically — each one shows the date it was read. Full disclosure.

Best for most

Best for most

Our pick on this page
Camco Camco Sidewinder Telescoping RV Sewer Hose Support, 20 ft
8.9/10

Camco Sidewinder Telescoping RV Sewer Hose Support, 20 ft

A rigid folding trough that holds the hose in a steady slope. Without one, the hose sags, the sag holds waste, and the smell you blame on the hose is actually the sag.

Read the full write-up or compare it with the rest below.

Quick picks

Four lengths across the two mechanisms that exist: Camco's rigid folding trough and Valterra's collapsing accordion. Scored on the published sewer rubric - crush resistance (30%), fittings (25%), storage (20%), build (15%), price (10%) - so the long supports lose points on storage honestly rather than being praised for reach alone.

#ProductBest forScorePrice
1
Camco Camco Sidewinder Telescoping RV Sewer Hose Support, 20 ft

Camco Sidewinder Telescoping RV Sewer Hose Support, 20 ft

A rigid folding trough that holds the hose in a steady slope. Without one, the hose sags, the sag holds waste, and the smell you blame on the hose is actually the sag.

Best for most
Giving the hose a continuous downhill run8.9/10
2
Camco Camco Sidewinder Telescoping RV Sewer Hose Support, 30 ft

Camco Sidewinder Telescoping RV Sewer Hose Support, 30 ft

The same telescoping folding trough as the 20 ft Sidewinder with half again the length, and the only support in this field that reaches 30 ft. Camco lists a carry strap with this one.

Only 30 ft option
A site where the sewer inlet is further away than 20 ft of trough will reach8.8/10
3
Valterra Valterra Slunky RV Drainage Hose Support, 20 ft, S2000

Valterra Slunky RV Drainage Hose Support, 20 ft, S2000

A coiled spring support that compresses to a fraction of a rigid trough's length. It gives a less precise slope, and it fits in a cabinet, which for most people is the better trade.

Packs smallest at 20 ft
Hose support that collapses to almost nothing9.0/10
4
Valterra Valterra Slunky RV Drainage Hose Support, 25 ft

Valterra Slunky RV Drainage Hose Support, 25 ft

The longest Slunky Valterra publishes. It collapses like a concertina instead of folding on hinges, which packs smaller than a rigid trough of the same length but gives up some of the fixed slope.

A long run where you want the support to roll up rather than fold flat8.7/10
5
Valterra Valterra S1500 Slunky RV Drainage Hose Support, 15 ft

Valterra S1500 Slunky RV Drainage Hose Support, 15 ft

The short Slunky. If your inlet is usually within a few steps of the outlet, 15 ft is the length that actually fits your pass-through and still gives the hose a continuous fall.

Best for short hookups
Short hookups where a 20 ft support is more trough than you need8.9/10

Tap any row to jump to the full write-up. Prices come from Amazon and are read automatically — see each product below for the date.

The short answer

Buy 20 ft. It matches the 20 ft hose kit that almost everyone owns, it covers the large majority of full-hookup pads, and it is the longest support that still fits a typical pass-through bay without eating all of it. Buy 30 ft only if you already know your usual sites put the inlet further away than 20 ft of hose will reach — and note that if you go that route your options narrow to one, because Camco’s Sidewinder is the only support in this field that reaches 30 ft. Valterra publishes Slunky lengths at 10, 15, 20 and 25 ft, and stops there. Go 15 ft if your pass-through is tight and your hookups are short; a 15 ft support with a 15 ft hose is a tidier setup than a 30 ft support you fold up into a quarter of its length every time.

The reason this is a real decision rather than a shrug is that a sewer hose support is not like a hose: more is not harmlessly better. The support has to span the whole length of hose you lay in it, because the moment the hose runs off the end of the trough it drops to the ground, and a drop is a low point. Low points hold waste between dumps. Waste held in a hose is the source of the smell people blame on the hose itself, and over a season it is also what degrades the hose from the inside. The setup sequence is built around this one principle: continuous fall, no exceptions.

So you cannot solve the awkward site by buying a 30 ft hose and keeping your 20 ft support. You either support the whole run or you accept a sag. And you cannot solve it the other way either — a 30 ft support with a 20 ft hose in it is 10 ft of empty plastic you carried there.

Continuous fall: an unbroken downhill slope from the trailer’s waste outlet to the site inlet, with no flat or rising sections anywhere along it. It is the single thing a support exists to create. A hose lying on the ground has fall at the start and the end and a belly in the middle, which is why it drains partially and then holds the rest.

Two mechanisms, not just two lengths

Before length, there is a design fork, and it changes which length is right for you. Camco and Valterra solve the same problem in genuinely different ways, and the longer you go the more the difference matters.

Camco Sidewinder - rigid folding trough

  • Hard plastic sections on snap-fit hinges that fold concertina-style
  • Telescopes, so you can use part of its length without unfolding it all
  • Holds the slope you set it to and keeps holding it on soft ground
  • The hinges are the long-term failure point
  • Bulky even folded - it owns a pass-through
  • The only family that reaches 30 ft (part 43061)

Valterra Slunky - collapsing accordion

  • A flexible concertina trough that squashes down lengthways
  • Packs far smaller than a rigid support of the same length
  • No hinges to crack, which removes the usual failure mode
  • Holds the slope less firmly - it can settle into soft ground
  • Accordion walls collect residue and want rinsing
  • Published in 10, 15, 20 and 25 ft. No 30 ft version

The practical consequence: if you are buying long, the rigid trough is the better mechanism because a 25 or 30 ft run is where slope discipline matters most and where an accordion is most likely to settle somewhere in the middle. If you are buying short, the accordion is the better mechanism because storage is the binding constraint and a 15 ft Slunky disappears into a bay a rigid support would fill.

What each length is actually for

LengthProductMechanismBuy it if
15 ftValterra Slunky S1500AccordionYour hookups are short and your pass-through is tight
20 ftCamco Sidewinder 43052Rigid foldingYou own a 20 ft hose kit - this is the default
20 ftValterra Slunky S2000AccordionSame length, smaller packed, less firm slope
25 ftValterra Slunky 25 ftAccordionLong runs, but you still need it to pack down
30 ftCamco Sidewinder 43061Rigid foldingYour sites genuinely need 30 ft and you have the bay for it
Published lengths and part numbers, read November 2026 from the makers' own listings. Folded dimensions and section counts are not published by either maker and are not stated here.

Twenty feet is the default for a reason. Sewer hose kits are overwhelmingly sold in 20 ft form — every kit on our sewer hose roundup is a 20 ft kit, usually two 10 ft sections — and matching the support to the hose is the whole game. Twenty feet covers the inlet position on the clear majority of full-hookup sites, and it is about the longest rigid support that leaves room in a pass-through for anything else.

Thirty feet is for a known problem, not an unknown one. The sites that defeat 20 ft are real: back-in pads where the inlet sits at the far corner, pull-through sites where the hookup serves two pads from the middle, older parks where the inlet was placed for a motorhome’s mid-body outlet rather than a trailer’s rear one, and any site where you have to route around a tree, a picnic table or a concrete pad edge. If you recognize your campground in that list, 30 ft is the right purchase and Camco’s 43061 is your only option, with a carry strap included per its listing. If you do not, 30 ft is 10 ft of plastic you fold up and put away unused every trip.

Fifteen feet is underrated. If you are a weekender at the same two or three parks with short hookups, a 15 ft support and a 15 ft hose is the setup that actually fits your bay, costs the least, and gives you the same continuous fall as anything longer. The failure case is clear and you should respect it: arrive at a site where the inlet is 18 ft away and you have a supported run plus an unsupported sag, which is worse than no support at all because it concentrates the low point.

The common mistake

Buying a 30 ft support to go with a 20 ft hose “for flexibility.” The extra 10 ft does nothing — the hose cannot reach into it. If you want the option of a longer run, the thing to buy is an extension hose and the longer support together, so the whole run stays off the ground. Buying the support alone just costs you storage.

How to decide, in about three minutes

  1. 1

    Measure your own hose, not the box

    Lay out what you actually carry, including any extension and the elbow. If you have 20 ft of hose, a 20 ft support is the match. If you have 20 ft plus a 10 ft extension you deploy twice a year, that is the case for 30 ft - but only if you deploy it.
  2. 2

    Think about the sites you use, not the worst one you can imagine

    Recall the last five hookups. If none of them needed more than 20 ft, buy 20 ft and keep the money. Buying for a hypothetical site is how a pass-through fills up with equipment that never gets used.
  3. 3

    Measure the pass-through before the support

    This is the step people skip. A folded rigid support is a long, rigid object, and it either goes in the bay or it travels in the truck bed. Measure the bay opening, not just its depth - a 30 ft support that fits diagonally but not through the door is no use.
  4. 4

    Pick the mechanism from the length

    Long run: rigid trough, because slope discipline matters more over distance. Short run and tight storage: accordion, because it packs away to nothing. At 20 ft both are reasonable and the choice is storage against firmness.
  5. 5

    Set the fall before you open anything

    Lay the support first, highest at the trailer, lowest at the inlet, then lay the hose in it and check by eye along its whole length for a flat section. Only then connect the elbow and pull the black tank valve. The order matters.
  6. 6

    Store it where the hose is not

    A support that has carried a hose is not clean. Keep it separate from the drinking water hose, in its own bag or bin - the storage options cover what works.

What to remember

  • The support must span the whole hose, or the unsupported part sags and holds waste.
  • Twenty feet matches the 20 ft hose kit almost everyone owns. It is the default.
  • Only Camco reaches 30 ft (part 43061). Valterra's Slunky stops at 25 ft.
  • Buy 30 ft for a known awkward site, never for a hypothetical one.
  • A 30 ft support with a 20 ft hose is 10 ft of plastic you carried for nothing.
  • Rigid trough holds the slope better; accordion packs away far smaller.
  • Measure the pass-through opening before you buy a long rigid support.

How we picked

We have not run these at a hookup and we do not own them. The comparison is built on the makers’ published lengths, part numbers and mechanism descriptions, read from their own current listings in November 2026 — Camco’s Sidewinder at 20 ft (43052) and 30 ft (43061), and Valterra’s Slunky at 15, 20 and 25 ft. Neither maker publishes folded dimensions or section counts, so this page does not state any; where we say a support is bulky folded that is a description of the mechanism, not a measurement we are passing off as a spec. The claim that Valterra makes no 30 ft Slunky is based on the lengths Valterra currently publishes and sells; if that changes, so will this page. Every listing was confirmed live and in stock before it was featured. Current prices come from retailer listing data read automatically and date-stamped — worth a look before you decide, because the price gap between these lengths is smaller than the length gap suggests and it moves. The rubric and its weights are published on how we pick.

The picks in full

Camco Camco Sidewinder Telescoping RV Sewer Hose Support, 20 ft
Best for most

Camco Sidewinder Telescoping RV Sewer Hose Support, 20 ft

Camco · Best for giving the hose a continuous downhill run

8.9/10

A rigid folding trough that holds the hose in a steady slope. Without one, the hose sags, the sag holds waste, and the smell you blame on the hose is actually the sag.

Key specifications

Length
20 ft
Type
Telescoping, folding
Material
Rigid plastic
Part
43052

Capacity figures read from Camco Sidewinder specifications, October 2026.

How it scored

  • Crush resistance (30%)8
  • Fittings (25%)6
  • Storage (20%)5
  • Build quality (15%)8
  • Price for capability (10%)8

The figures above, at the weights above, converted to our published 8.4–9.8 scale by one site-wide formula. Both the weights and the formula are on how we pick, so this number is reproducible from this card.

Why we picked it

  • Rigid, so the slope stays where you set it
  • Folds and telescopes for storage
  • Keeps the hose off gravel, which is what kills hoses

Good to know

Bulky even folded

Camco Camco Sidewinder Telescoping RV Sewer Hose Support, 30 ft
Only 30 ft option

Camco Sidewinder Telescoping RV Sewer Hose Support, 30 ft

Camco · Best for a site where the sewer inlet is further away than 20 ft of trough will reach

8.8/10

The same telescoping folding trough as the 20 ft Sidewinder with half again the length, and the only support in this field that reaches 30 ft. Camco lists a carry strap with this one.

Key specifications

Length
30 ft
Type
Telescoping, folding
Material
Rigid plastic
Part
43061

Capacity figures read from Camco Sidewinder 30 ft listing, part 43061, October 2026.

How it scored

  • Crush resistance (30%)8
  • Fittings (25%)6
  • Storage (20%)4
  • Build quality (15%)8
  • Price for capability (10%)7

The figures above, at the weights above, converted to our published 8.4–9.8 scale by one site-wide formula. Both the weights and the formula are on how we pick, so this number is reproducible from this card.

Why we picked it

  • Reaches inlets that defeat a 20 ft support
  • Carry strap included per the listing
  • Telescopes down, so you are not forced to use the full length

Good to know

Takes up noticeably more pass-through than the 20 ft version

Valterra Valterra Slunky RV Drainage Hose Support, 20 ft, S2000
Packs smallest at 20 ft

Valterra Slunky RV Drainage Hose Support, 20 ft, S2000

Valterra · Best for hose support that collapses to almost nothing

9.0/10

A coiled spring support that compresses to a fraction of a rigid trough's length. It gives a less precise slope, and it fits in a cabinet, which for most people is the better trade.

Key specifications

Length
20 ft extended
Type
Coiled spring support
Storage
Compresses to about 2 ft
Color
Black

How it scored

  • Crush resistance (30%)6
  • Fittings (25%)6
  • Storage (20%)10
  • Build quality (15%)7
  • Price for capability (10%)8

The figures above, at the weights above, converted to our published 8.4–9.8 scale by one site-wide formula. Both the weights and the formula are on how we pick, so this number is reproducible from this card.

Why we picked it

  • Collapses small enough to store anywhere
  • Light
  • Flexes around an awkward site layout

Good to know

Slope is less consistent than a rigid trough

Valterra Valterra Slunky RV Drainage Hose Support, 25 ft

Valterra Slunky RV Drainage Hose Support, 25 ft

Valterra · Best for a long run where you want the support to roll up rather than fold flat

8.7/10

The longest Slunky Valterra publishes. It collapses like a concertina instead of folding on hinges, which packs smaller than a rigid trough of the same length but gives up some of the fixed slope.

Key specifications

Length
25 ft
Type
Collapsing accordion trough
Material
Flexible plastic
Pack
1

Capacity figures read from Valterra published Slunky hose support range, October 2026.

How it scored

  • Crush resistance (30%)6
  • Fittings (25%)5
  • Storage (20%)8
  • Build quality (15%)7
  • Price for capability (10%)7

The figures above, at the weights above, converted to our published 8.4–9.8 scale by one site-wide formula. Both the weights and the formula are on how we pick, so this number is reproducible from this card.

Why we picked it

  • Collapses far smaller than a rigid 25 ft support
  • No hinges to snap, which is the usual failure on folding troughs
  • Reaches most long-run sites without going to a 30 ft rigid support

Good to know

Holds the slope less firmly than a rigid trough - it can settle on soft ground

Valterra Valterra S1500 Slunky RV Drainage Hose Support, 15 ft
Best for short hookups

Valterra S1500 Slunky RV Drainage Hose Support, 15 ft

Valterra · Best for short hookups where a 20 ft support is more trough than you need

8.9/10

The short Slunky. If your inlet is usually within a few steps of the outlet, 15 ft is the length that actually fits your pass-through and still gives the hose a continuous fall.

Key specifications

Length
15 ft
Type
Collapsing accordion trough
Material
Flexible plastic
Part
S1500

Capacity figures read from Valterra published Slunky hose support range, October 2026.

How it scored

  • Crush resistance (30%)6
  • Fittings (25%)5
  • Storage (20%)9
  • Build quality (15%)7
  • Price for capability (10%)9

The figures above, at the weights above, converted to our published 8.4–9.8 scale by one site-wide formula. Both the weights and the formula are on how we pick, so this number is reproducible from this card.

Why we picked it

  • Packs into a space a 20 or 30 ft support will not fit
  • Cheapest honest way to stop the hose sagging
  • Enough length for the majority of full-hookup pads

Good to know

Runs out on a long or offset hookup, and a part-supported hose is a sagging hose

Our recommendation

Of the 5 picks above, these are the two to choose between.

Camco Camco Sidewinder Telescoping RV Sewer Hose Support, 20 ft

Our pick

Camco Sidewinder Telescoping RV Sewer Hose Support, 20 ft

8.9/10

Best for giving the hose a continuous downhill run. A rigid folding trough that holds the hose in a steady slope. Without one, the hose sags, the sag holds waste, and the smell you blame on the hose is actually the sag.

Camco Camco Sidewinder Telescoping RV Sewer Hose Support, 30 ft

Runner-up

Camco Sidewinder Telescoping RV Sewer Hose Support, 30 ft

8.8/10

Best for a site where the sewer inlet is further away than 20 ft of trough will reach. The same telescoping folding trough as the 20 ft Sidewinder with half again the length, and the only support in this field that reaches 30 ft. Camco lists a carry strap with this one.

Common questions

Only if your sites genuinely need it. Twenty feet matches the hose kit most people own. A 30 ft support with a 20 ft hose is 10 ft of plastic you carried for nothing.

Sources

Brands: want your product tested? For Brands.